Căutare 2011 fascicula8 nr1 după Titlu
Afișează articolele 1-20 of 23
-
Analysis of the PM Bearing – Spindle Contact Using Finite Element Method
(UDJG, 2011)Using PM (Powder Metallurgy) technologies, new antifriction materials based on iron-copper powders with different addition elements were developed. The elemental powder mixtures were compacted at different pressures and ... -
Durability of the Layers Deposed with Metal – Ceramic Powders Type CR3 C2 –NICR and High Speed Flame (HVOF)
(UDJG, 2011)The durability of the reconditioned or preventively covered with powders type Cr3 C2 –NiCr product may outrun the performances of the original product and (the original specification, too). Due to the deposit of these ... -
Ecological Lubricants Based on Vegetal Oils
(UDJG, 2011)Recently, there is an ecologically justified tendency to use lubricants based on vegetal oils and synthetic fluids, both ones reducing the application field of mineral oils. Biodegradable lubricants will be more used in ... -
Elastic Frictional Contact under Normal and Tangential Loading
(UDJG, 2011)A robust algorithm for elastic contact simulation considering tangential tractions is advanced in this paper. Two similar numerical models are advanced for the normal, as well as for the tangential direction, and the ... -
Experimental Determination of Contact Area Between a Sphere and a Circular Plate Using a Technique Based on Laser Profilometry
(UDJG, 2011)This paper presents the experimental determination of contact area between a steel sphere and a sapphire circular plate, using a technique based on laser profilometry. The reflectivity value is smaller inside contact area ... -
Experimental Preliminary Research Regarding Normally and Tangentially Loaded Contacts
(UDJG, 2011)The purpose of this paper is to determine the contact area for a contact between a steel sphere and a sapphire disk loaded normally and tangentially, using laser profilometry. For this, was used an experimental device ... -
Hydrogen Wear of the Slab Continuous Casting Guiding Tribosystems
(UDJG, 2011)The steel continuous casting equipment consists of a set of technical systems which, tribologically, may be regarded as tribological systems. The process model contains input –output, command and control parameters. Both ... -
Kinematic and Dynamic Aspects of Damped Collision Between Two Metallic Balls
(UDJG, 2011)Recently, a new model of the behaviour of a collision has been proposed by Flores. The model describes the behaviour during the impact of a complete range of metallic materials, from the soft to the hard ones. The present ... -
A Method to Evaluate the Durability of Sucker Rod Pumps and to Reduce Corrosive Wear
(UDJG, 2011)The paper presents experimental tests made in static and dynamic conditions in order to establish the wear laws for different materials’ couples at different medium temperatures and pressures. Some complex wear laws were ... -
Modelling of Some Degradation Processes by Corrosion Fatigue of Metallic Surfaces
(UDJG, 2011)Based on the well known fatigue corrosion effects, the mechanical stress and the corrosive environment have a significant effect on the prediction of the lifespan of the equipments that work in corrosive environment, two ... -
Modelling of some Degradation Processes by Corrosion Fatigue of Metallic Surfaces
(UDJG, 2011)Based on the well known fatigue corrosion effects, the mechanical stress and the corrosive environment have a significant effect on the prediction of the lifespan of the equipments that work in corrosive environment, two ... -
Roughness as Small Surface Defects and Microstructure Changes in the Fatigue Process
(UDJG, 2011)Examinations in detail using X-radiation diffraction of the dislocation substructure in fine-grained S355JR steels plate specimen fatigued with constant amplitude were carried out to investigate the correlation between the ... -
A Simple Device for Modelling Bioarticular Joint Friction
(UDJG, 2011)In this paper a simple device for modelling bioarticular friction is presented. The experimental device serves to simulate the movement as it would take place in a knee joint. Key components of the experimental device are ... -
Some Experimental Results Concerning the Influence of Surface Coatings on the Wear of Poly-Ether-Etherketone (Peek) Polymeric Gears
(UDJG, 2011)Gears made of general purpose Poly-Ether-Ether-Ketone (PEEK) polymeric material and coated on their flanks with a thin layer of different solid lubricants MoS2, graphite (C), BN and PTFE are tested in relation to wear and ... -
Studies Regarding the Influence of Carbon Content on the Tribological Behaviour of Gas-Carbu-Sintering Steels
(UDJG, 2011)The paper presents the experimental research on the tribological behavior of sintered steels obtained by carburizing the iron powder with different concentrations of graphite (Gr). For the experimental research were prepared ... -
Surface Roughness Parameters Evaluation in Rolling/Sliding Wear TestsS
(UDJG, 2011)Rolling/sliding wear tests were performed on an Amsler test rig. Normal load (expressed as the Hertzian pressure) and the roll-slide ratio have been considered to have the most important influence in simulating gear ... -
Technological Providing of Surface Layer Wear Resistance of Machine Components
(UDJG, 2011)The article describes the problem of assuring the wear resistance of the friction surface layers based on the control of the geometrical, physical and mechanical properties to be formed after the machining process. -
The Application of CRN Coating in Sliding Pairs under Lubrication Conditions
(UDJG, 2011)This work revealed the results of the impact of the formed surface layer CrN and the surfaces layer CrN-steel 46Cr2 “ring” structure. The sliding pairs worked under conditions of lubricating the friction area with Lotos ... -
The Dynamic Behavoir of the Sliding Tribosystem in Cyclical Translation Motion in Unsteady Duty
(UDJG, 2011)The present paper deals with certain methodological aspects of researching the behaviour of the sliding tribosystem in cyclical translation motion from the point of view of the dynamics of contact processes. The dynamic ... -
The Influence of Nano-Particle Additive to Lubricating Oils on the Structure and Properties of Friction Surfaces
(UDJG, 2011)The article considers the influence of the additive in the lubricating oils Cermet, on tribological properties of a friction pair «cast iron – chrome», which is typical for the cylinder-piston unit of engines. It is shown ...
